![](https://digilib.itb.ac.id/assets/icon/pdf.gif)
ABSTRAK Ahmad Hidayatullah
Terbatas  Irwan Sofiyan
» Gedung UPT Perpustakaan
Terbatas  Irwan Sofiyan
» Gedung UPT Perpustakaan
Solar and wind generation’s share in the ASEAN region will reach 20% by 2030
(from just over 1% in 2022) in ASEAN and 69% by 2050. Indonesia’s renewable
energy potential for power generation from offshore wind is up to 589 GW (IRENA
2022). Wind turbines are moving further to deeper waters and capturing higher
wind speeds in harsher environments. This trend creates additional challenges in
the design, installation, operation, maintenance, and decommissioning phases of an
offshore wind farm (Ramachandran et al, 2021). There is a novel installation
procedure by performing mating at calm water and towing complete structure
vertically, such as Aasta Hansteen Spar (O&G) (2018), Hywind Scotland Pilot Park
(FOWT) (2017), and Hywind Tampen (FOWT) (2022). This installation method
(inshore) is considered more cost-effective than an offshore installation (Myhr et al,
2014).
In this study, a floating offshore wind turbine (FOWT) is designed to be transported
from the fabrication yard. The mating procedure is performed near the fabrication
yard. Then vertical full assembly tow out is performed to an in-place location at
Jeneponto Regency, South Sulawesi. The relevant standard from DNVGL-STN001.
The analysis was performed to obtain towing configuration, specification,
and tug bollard pull (BP). The critical condition of holding the tow position in
severe weather conditions is considered limiting and hence used for verification of
towing static bollard pull, configuration, and stability.
The mating point chosen at 100 m, bathymetry data, and environmental conditions
are considered in the process. The environmental condition along the route is
analyses. Several aspects as bathymetry, under keel clearance, and existing
projected platform and subsea assets are considered in the proposed tow route plan.
The phase 1 towing of substructure ballast configuration is designed using
hydrostatic stability software so that the stability criteria of intact and damaged
complies with the standard with a critical margin of 7% area ratio of wind heeling
arm. The towing configuration is proposed to maintain a 100-yr sea state
( ???????? = 3.67 ????, ???????? = 10.8 ????, ????10 = 20 ????. ?????1, ???????? = 110 ????????. ?????1) and analyses
with radiation diffraction software and hydrodynamic stability software for 3-hour
simulation. The result consists of a minimal deployable towline length (DTL) of
500 m using 76 mm wire rope, 60o bridle apex, shackles and delta MBL of 221 tons.
The static BP of 57 tons using Chaterine Queen AHTS of 85-ton BP.
The phase 2 full assembly towing configuration is proposed to maintain
unrestricted operation condition (???????? = 5 ????, ????10 = 20 ????. ?????1, ???????? = 204 ????????. ?????1)
and analyses with radiation diffraction software and hydrodynamic stability
software for 3-hour simulation. The result consists of a minimal deployable towline
length (DTL) of 500 m using 76 mm wire rope, and shackles and a delta MBL of
439 tons. The BP tug required for a single leading tug is 273 tons.
This study also covers station-keeping analysis. The relevant standard using
DNVGL-ST-0119. The mooring system is analyses with radiation diffraction
software and hydrodynamic stability software for a 3-hour simulation. The iteration
of mooring line configuration, specification, and anchor radius are performed to
obtain the optimal design. The critical condition of ultimate limit state (ULS) at
parked with 50-yr environmental condition, ULS at rated speed at the highest thrust
coefficient (???????? ) with 50-yr wave and 1-yr current environmental condition, and
accidental limit states (ALS) survival condition with 500-yr abnormal
environmental condition are analyses. The cases are considered limiting and hence
used for verification of mooring effective tension, tower inclination, and floater
offset.
Mooring system station-keeping analysis for ultimate limit states (ULS) and
accidental limit states (ALS) resulting 3 spread lines with bridle line; configuration
one of anchor radius of 935 m; combination of 50 m bridle chain line with nominal
diameter 54 mm, and 885m chain line with nominal diameter 73 mm, maximum
response of 5.6o tilt and 46.7 m floater offset; alternative configuration two of
anchor radius of 528 m; combination of 50 m bridle chain line with nominal
diameter 54 mm, 38 m chain line with nominal diameter 73 mm, 100 m polyester
line with nominal diameter 152 mm, and 340 m heavy chain line with nominal
diameter 127 mm; maximum design value of 5.6o rotor tilt and 42.0 m floater offset.