EVALUASI DAN PERANCANGAN SEPARATOR DUA FASE UNTUK ALIRAN FLUIDA GAS 500 MMSCFD DARI DUA LAPANGAN PRODUKSI BARU (STUDI KASUS: FPU JANGKRIK) TUGAS SARJANA Diajukan sebagai salah satu syarat untuk memperoleh gelar Sarjana Teknik Oleh Laksmana Kinasih Providentia Dei 13120118 PROGRAM STUDI TEKNIK MESIN FAKULTAS TEKNIK MESIN DAN DIRGANTARA INSTITUT TEKNOLOGI BANDUNG Tahun 2024 ii LEMBAR PENGESAHAN Tugas Sarjana EVALUASI DAN PERANCANGAN SEPARATOR DUA FASE UNTUK ALIRAN FLUIDA GAS 500 MMSCFD DARI DUA LAPANGAN PRODUKSI BARU (STUDI KASUS: FPU JANGKRIK) Oleh Laksmana Kinasih Providentia Dei 13120118 Program Studi Teknik Mesin Fakultas Teknik Mesin dan Dirgantara Institut Teknologi Bandung Disetujui pada Tanggal : 2 Agustus 2024 Pembimbing Utama Prof. Ir. I Gusti Nyoman Wiratmaja, Ph.D. NIP 19631221 198903 1 001 ii Tugas Sarjana Judul Evaluasi dan Perancangan Separator Dua Fase untuk Aliran Fluida Gas 500 MMSCFD dari Dua Lapangan Produksi Baru Studi Kasus: FPU Jangkrik Laksmana Kinasih Providentia Dei Program Studi Teknik Mesin 13120118 Fakultas Teknik Mesin dan Dirgantara Institut Teknologi Bandung Abstrak Energi merupakan kunci utama dari pertumbuhan ekonomi suatu negara sebagai penyokong dari seluruh aktivitas produksi dan konsumsi yang dilakukan warga negara. Seiring dengan kenaikan konsumsi energi pertahunnya, upaya pemenuhan kebutuhan energi dalam negeri perlu dilakukan lewat kegiatan eksplorasi dan produksi sesuai dengan yang dijelaskan dalam Undang-Undang Nomor 30 Tahun 2007. Salah satu aktivitas eksplorasi yang telah dilakukan adalah penemuan Lapangan Maha, yang direncanakan akan di-tie-in ke FPU Jangkrik yang sebelumnya telah digunakan untuk memproduksi Lapangan Jangkrik. Tugas sarjana ini membahas evaluasi terhadap kecukupan kapasitas separator dua fase yang digunakan sebagai slug catcher yang terdapat di FPU Jangkrik perlu dilakukan untuk mengetahui apakah separator dua fase tersebut dapat mengakomodasi aliran tambahan. Setelah evaluasi dilakukan, akan dilakukan perancangan separator baru dengan menentukan ukuran, mechanical design, dan juga estimasi biaya modul dasar peralatan, dengan mengacu kepada kode, standar, dan referensi lain yang relevan. Hasil analisis menunjukkan bahwa slug catcher existing tidak dapat mengakomodasi aliran tambahan baik dari Lapangan Merakes, maupun Lapangan Merakes dan Maha, dan ditemukan bahwa slug catcher existing hanya dapat menerima aliran tambahan sebesar 85 MMSCFD. Dengan demikian, dirancanglah sebuah separator baru dengan diameter 5000 mm dan panjang 9220 mm dengan ketebalan nominal shell sebesar 110 mm yang dapat mengakomodasi pemisahan aliran fluida 500 MMSCFD dari Lapangan Merakes dan Maha. Adapun, berdasarkan analisis teoretis, diperoleh rentang estimasi biaya untuk pembuatan separator tersebut berkisar pada Rp 5.960.000.000 – 23.836.300.000. Kata kunci: perancangan, pemisahan, separator, pressure vessel, mechanical design, estimasi biaya iii Undergraduate Thesis Title Evaluation and Design of a Two-Phase Separator for 500 MMSCFD Gas Fluid Flow from Two New Production Fields Case Study: FPU Jangkrik Laksmana Kinasih Providentia Dei Major Mechanical Engineering 13120118 Faculty of Mechanical and Aerospace Engineer Institut Teknologi Bandung Abstract Energy is the key to a country's economic growth as it supports all production and consumption activities carried out by its citizens. Along with the annual increase in energy consumption, efforts to meet domestic energy needs must be made through exploration and production activities as explained in Undang-Undang Nomor 30 Tahun 2007. One of the exploration activities that has been carried out is the discovery of the Maha Field, which is planned to be tied into the Jangkrik FPU, which has previously been used to produce the Jangkrik Field. This undergraduate thesis discusses the evaluation of the adequacy of the two-phase separator capacity used as a slug catcher in the Jangkrik FPU to determine whether the two- phase separator can accommodate additional flow. After the evaluation is conducted, a new separator will be designed by determining its size, mechanical design, and cost estimation of the basic equipment module, referring to code, standard, and other relevant references. The analysis results show that the existing slug catcher cannot accommodate additional flow from either the Merakes Field or both the Merakes and Maha Fields, and it was found that the existing slug catcher can only handle an additional flow of 85 MMSCFD. Therefore, a new separator with a diameter of 5000 mm and a length of 9220 mm with a nominal shell thickness of 110 mm is designed to accommodate fluid separation of 500 MMSCFD from the Merakes and Maha Fields. Based on theoretical analysis, the estimated cost range for manufacturing the separator is between Rp 5,960,000,000 and Rp 23,836,300,000. Keywords: design, separation, separator, pressure vessel, mechanical design, cost estimate.