DESAIN SUMUR GAS LIFT PADA SUMUR X DI LAPANGAN ONWJ DENGAN SENSITIVITY TERHADAP KEDALAMAN TITIK INJEKSI, LAJU INJEKSI, UKURAN TUBING DAN PERHITUNGAN FORCE BALANCE TUGAS AKHIR Mohamad Rizky Pahlevy NIM 12214025 Diajukan sebagai salah satu syarat untuk memperoleh gelar SARJANA TEKNIK pada Program Studi Teknik Perminyakan PROGRAM STUDI TEKNIK PERMINYAKAN FAKULTAS TEKNIK PERTAMBANGAN DAN PERMINYAKAN INSTITUT TEKNOLOGI BANDUNG 2018 DESAIN SUMUR GAS LIFT PADA SUMUR X DI LAPANGAN ONWJ DENGAN SENSITIVITY TERHADAP KEDALAMAN TITIK INJEKSI, LAJU INJEKSI, UKURAN TUBING DAN PERHITUNGAN FORCE BALANCE Mohamad Rizky Pahlevy*, Silvya Dewi Rahmawati**,Farasdaq Muchibbus Sajjad*** Hak cipta 2018, Institut Teknologi Bandung Sari Gas lift merupakan metode artficial lift yang umum digunakan dalam industri perminyakan yang bertujuan untuk meningkatkan laju produksi pada sumur dengan tekanan reservoir yang sudah relatif rendah maupun pada sumur yang tidak dapat mengalir secara alami. Untuk meningkatkan produksi suatu sumur gas lift perlu dilakukan identifikasi permasalahan-permasalahan yang nantinya dapat dilakukan beberapa rekomendasi terhadap masalah-masalah tersebut, hal ini sangat penting dilakukan mengingat bahwa sumur yang akan dilakukan studi memiliki potensi produksi yang lebih optimum. Studi ini menyimpulkan bahwa untuk meningkatkan hasil perolehan minyak dalam suatu sumur gas lift diperlukan sensitivity terhadap faktor-faktor yang mempengaruhi laju produksi sehingga dapat memaksimalkan produksi suatu sumur. Desain sumur gas lift dapat dilakukan dengan melakukan sensitvity laju gas injeksi sehingga didapatkan gas lift performance curve yang berguna untuk menentukan berapa laju gas injeksi yang paling optimum, selanjutnya dilakukan sensitivity ukuran tubing pada sumur dengan analisis nodal yaitu dengan membuat kurva Vertical Lift Performance (VLP) vs kurva Inflow Performance relationship (IPR) dengan variable ukuran tubing yang berbeda-beda sehingga didapatkan ukuran tubing paling optimum. Selanjutnya melakukan penentuan kedalaman titik injeksi, semakin dalam gas diinjeksikan kedalam sumur maka laju produksi akan semakin meningkat tetapi dibutuhkan tekanan kompresor yang lebih tinggi. Tahap selanjutnya adalah melakukan spacing design untuk menentukan letak unloader valve dan orifice untuk proses unloading dan injeksi. Terakhir, perhitungan metode force balance untuk mengetahui besarnya tekanan yang bekerja pada valve pada saat proses unloading dan operating. Perhitungan tekanan yang bekerja pada valve dilakukan pada saat proses displacemet killing fluid dan pada saat operasi injeksi gas. Kata kunci: Artificial Lift, Gas Lift, laju injeksi, titik injeksi, ukuran tubing, spacing design, Force Balance. Abstract Gas lift is an artficial lift method commonly used in the petroleum industry which aims to increase the production rate at wells with relatively low reservoir pressure as well as on wells that can not flow naturally. To increase the production of a gas lift well, it is necessary to identify problems which later can be made some recommendations to those problems, this is very important to do, considering that the wells to be conducted have more optimum production potential. This study concludes that to increase the yield of oil in gas lift well, sensitivity to factors affecting production rate is needed to maximize the production of a well. Design of gas lift wells can be done by doing sensitvity rate of injection to get gas lift performance curve which is useful to determine how the rate of injection gas rate is the most optimum, then the sensitivity of the tubing size at the well with nodal analysis by making Vertical Lift Performance (VLP) curves vs Inflow Performance relationship (IPR) curves with different tubing size variables to obtain the optimum tubing size. Then, determining the depth of the injection point, the deeper gas is injected into the well then the production rate will increase but the higher compressor pressure is required. The next step is spacing design analysis to get the location of the unloader and orifice for unloading and injection process. Finally, force balance calculation method is used to find out the amount of pressure that works on the valve at the time of unloading and operating. The calculation of the pressure acting on the valve is carried out at the process of displacemet killing fluid and at the time of gas injection operation. Keywords: Artificial Lift, Gas Lift, injection point, tubing size, spacing design, Force Balance. *) Mahasiswa Program Studi Teknik Perminyakan ITB, Institut Teknologi Bandung, angkatan 2014 **) Dosen Pembimbing Program Studi Teknik Perminyakan, Institut Teknologi Bandung ***) Pembimbing lapangan, PHE Offshore North West Java.